Fenix E20 V2.0

Product description

Fenix the E20 V2.0 is the latest generation of LED luminaire, offering high lumen output up to 350 lumens (ANSI) and a range of up to 126 meters. This version offers easy operation and four levels of light output with a run time of up to 200 hours. The control and switching on is done by the end button. It uses two commonly available pencil batteries for power, of course disposable and rechargeable batteries can be used. A unique innovation is a special collimator that creates a light cone with a range of 126 meters. The collimator is made with technology used in the automotive industry and its height is only 3 millimeters, less than half that of commonly used optics. With a length of only 127 millimetres and a weight of 42 grams (without batteries), it can be carried with you at all times. This luminaire is an ideal lighting tool with an excellent ratio of high performance, quality and price. All luminaire parameters (luminous flux, battery life, waterproofness, range, and impact resistance) are measured in accordance with ANSI/NEMA FL 1-2009. The Fenix E20 V2.0 replaces the older Fenix L2T V2.0, Fenix E20 and Fenix E21 models.

Features:
- Modern LED Luminus SST-20 with 50 000 hours lifetime is used
- Four power modes: measured with rechargeable NiMH battery with 1900mAh capacity: 350 lumens: (1.5 hours) -> 150 lumens (5.5 hours) -> 30 lumens (34.5 hours) -> 5 lumens (140 hours) measured with included alkaline batteries: 350 lumens (3.75 hours) -> 150 lumens (11.25 hours) -> 30 lumens (93.5 hours) -> 5 lumens (200 hours)
- Uses two pencil batteries (AA type - alkaline, lithium or rechargeable NiMH)
- These batteries are cheap and widely available
- Energizer L91 Ultimate Lithium pencil batteries (especially suitable for extreme conditions and expeditions) provide the longest battery life
- Protection against accidental insertion of batteries in reverse (reverse polarity)
- Intelligent overheating protection
- Electronics with digital constant power control and protection against reverse insertion of batteries
- Made of T6 aircraft hardened aluminium, the luminaire is shockproof against drops from a height of 1 metre
- Durable surface - Type III hard anodized
- Distinctive surface grooving for better grip
- Fixed clip for safe and easy carrying (removable)
- Special super-thin collimator only 3 mm high, made with technology used in the automotive industry
- Range 126 meters (3950 cd)
- Waterproof and dustproof to IP68 standard (tested underwater at a depth of 2 meters)
- Dimensions 12.7 cm (length) x 1.68 cm (body diameter) x 2.1 cm (head diameter)
- Weight 42 grams (without batteries)
- The flashlight comes with a wrist lanyard, a spare o-ring and two alkaline batteries
- As optional original accessories can be purchased: diffuser AOD-S, red filter AOF-S, traffic cone AOT-S, swivel belt clip, bike holder Fenix, strap for using the flashlight as a headlamp or case ALP-MT
- Also compatible with the LockBlocks bike holder, BikeBlock bike helmet holder

Using the LED luminaire Fenix E20 V2.0
To switch on, press the switch located at the end of the luminaire.The lamp always switches on in the lowest mode. With the lamp on, you can change power modes at any time at the gentle touch of a button (cycles through low - medium - high - turbo).

Intelligent overheating protection - if the temperature of the luminaire rises above 58°C, it will automatically start to reduce the power in gradual steps of 1% every second until the power is reduced to 150 lumens. As soon as the temperature of the luminaire drops below 58°C, the output is automatically increased to the original level again. Thus, operation at the highest power mode is not limited by time, but only by temperature.

Low battery warning - if the battery voltage drops below the set level, the luminaire will automatically reduce power. When the batteries are low, only the lowest power mode will be available.

Warning Do not disassemble the sealed part in the lamp head yourself, this will breach the warranty. Remove the batteries from the luminaire if they are dead. Especially with disposable batteries, there is a risk of leakage and subsequent damage to the luminaire. If the protective rubber rings appear damaged after prolonged use, replace them. The rings also need to be lubricated to prevent erosion of the rubber. By following these rules, the luminaire will be properly protected against water. If the lamp is flickering, not switching to higher power modes, or not lighting up, it could be one of the following reasons: the batteries are almost dead - replace them. The contacts inside the lamp are clogged - clean them with a cotton swab dipped in alcohol. The back of the lamp is loose - add lubricant to the sealing rings and tighten.

Parameters

Features:
- Modern LED Luminus SST-20 with 50 000 hours lifetime is used
- Four power modes: measured with rechargeable NiMH battery with 1900mAh capacity: 350 lumens: (1.5 hours) -> 150 lumens (5.5 hours) -> 30 lumens (34.5 hours) -> 5 lumens (140 hours) measured with included alkaline batteries: 350 lumens (3.75 hours) -> 150 lumens (11.25 hours) -> 30 lumens (93.5 hours) -> 5 lumens (200 hours)
- Uses two pencil batteries (AA type - alkaline, lithium or rechargeable NiMH)
- These batteries are cheap and widely available
- Energizer L91 Ultimate Lithium pencil batteries (especially suitable for extreme conditions and expeditions) provide the longest battery life
- Protection against accidental insertion of batteries in reverse (reverse polarity)
- Intelligent overheating protection
- Electronics with digital constant power control and protection against reverse insertion of batteries
- Made of T6 aircraft hardened aluminium, the luminaire is shockproof against drops from a height of 1 metre
- Durable surface - Type III hard anodized
- Distinctive surface grooving for better grip
- Fixed clip for safe and easy carrying (removable)
- Special super-thin collimator only 3 mm high, made with technology used in the automotive industry
- Range 126 meters (3950 cd)
- Waterproof and dustproof to IP68 standard (tested underwater at a depth of 2 meters)
- Dimensions 12.7 cm (length) x 1.68 cm (body diameter) x 2.1 cm (head diameter)
- Weight 42 grams (without batteries)
- The flashlight comes with a wrist lanyard, a spare o-ring and two alkaline batteries
- As optional original accessories can be purchased: diffuser AOD-S, red filter AOF-S, traffic cone AOT-S, swivel belt clip, bike holder Fenix, strap for using the flashlight as a headlamp or case ALP-MT
- Also compatible with the LockBlocks bike holder, BikeBlock bike helmet holder

Using the LED luminaire Fenix E20 V2.0
To switch on, press the switch located at the end of the luminaire.The lamp always switches on in the lowest mode. With the lamp on, you can change power modes at any time at the gentle touch of a button (cycles through low - medium - high - turbo).

Intelligent overheating protection - if the temperature of the luminaire rises above 58°C, it will automatically start to reduce the power in gradual steps of 1% every second until the power is reduced to 150 lumens. As soon as the temperature of the luminaire drops below 58°C, the output is automatically increased to the original level again. Thus, operation at the highest power mode is not limited by time, but only by temperature.

Low battery warning - if the battery voltage drops below the set level, the luminaire will automatically reduce power. When the batteries are low, only the lowest power mode will be available.

Warning Do not disassemble the sealed part in the lamp head yourself, this will breach the warranty. Remove the batteries from the luminaire if they are dead. Especially with disposable batteries, there is a risk of leakage and subsequent damage to the luminaire. If the protective rubber rings appear damaged after prolonged use, replace them. The rings also need to be lubricated to prevent erosion of the rubber. By following these rules, the luminaire will be properly protected against water. If the lamp is flickering, not switching to higher power modes, or not lighting up, it could be one of the following reasons: the batteries are almost dead - replace them. The contacts inside the lamp are clogged - clean them with a cotton swab dipped in alcohol. The back of the lamp is loose - add lubricant to the sealing rings and tighten.

Video

Question on product

Bargain packages